• MrMoon5shine's Avatar
    02-16-2019
    60% is the number I found for amazon's self publishing, on demand to paper back minus printing cost. https://kdp.amazon.com/en_US/help/topic/G8BKPU9AGVZSF9QF that's amazon page on the print selling side of the deal, there is also a ebook deal to sell to kindle users I think
    46 replies | 1469 view(s)
  • MrMoon5shine's Avatar
    12-29-2018
  • MrMoon5shine's Avatar
    12-29-2018
    MrMoon5shine replied to a thread Spider Leg: Basic Setup in MBTV
    well done, nice simple easy instructions :)
    10 replies | 495 view(s)
  • MrMoon5shine's Avatar
    12-27-2018
    kinda both, root rot according to a local arbortis. wedged its self against the cedar pretty tight
    9 replies | 356 view(s)
  • MrMoon5shine's Avatar
    12-26-2018
    Unfountantiy not my job :( but if i happen to be around when they are doing i will grab a few shots :)
    9 replies | 356 view(s)
  • MrMoon5shine's Avatar
    12-26-2018
    just thought you guys and gals might get a kick out of seeing this one :) we have had a few wind storms with lots of rain the last two weeks, it's a douglas fir. fortunately its a work shop and not a house :)
    9 replies | 356 view(s)
  • MrMoon5shine's Avatar
    05-21-2018
    my .02 clean up the trunks first ie remove all small branches first, so you can see the tension better :) and less of a chance of tripping or getting whacked in the head
    38 replies | 1399 view(s)
  • MrMoon5shine's Avatar
    05-05-2018
    well done good sir!
    52 replies | 2038 view(s)
  • MrMoon5shine's Avatar
    04-12-2018
    when using mirrors, don't try to guess how far it is in feet or meters to the trailer instead just keep halving the distance :) lots of small corrections are bests... my two cents
    124 replies | 6246 view(s)
  • MrMoon5shine's Avatar
    03-25-2018
    ohhh could you imagine getting pulled by boat in one? haha i think that would be a blast
    18 replies | 677 view(s)
  • MrMoon5shine's Avatar
    02-16-2017
    nice one :boogie:
    8 replies | 684 view(s)
  • MrMoon5shine's Avatar
    01-18-2017
    would it also work as a redirect? if you were to clip the second tie to a different anchor point.
    15 replies | 1935 view(s)
  • MrMoon5shine's Avatar
    01-18-2017
    thanks did not known that, always learning!
    37 replies | 3814 view(s)
  • MrMoon5shine's Avatar
    01-17-2017
    on a side note, maybe you know, some tree types can be every detrimental to garden health. once know a lady who mulched her garden with cedar chips, not much would grow after that.
    37 replies | 3814 view(s)
  • MrMoon5shine's Avatar
    01-17-2017
    I would suggest building a screening deck to separate the chips by size, one small enough to use atm and the rest through in a pile to rot for a few years first.
    37 replies | 3814 view(s)
  • MrMoon5shine's Avatar
    01-12-2017
    nice site! love the pictures you have a double post in the testimonial page I would put phone number and email front and center under your nav links, don't see it up top very well. maybe not the email but phone number for sure N.H. counties where is that? maybe type it out long form at least once, people from the area might know where that is but you're on the world wide web now :) the math question to send you a message a has no explanation I always like to see a physical address some were, if you are running out of your home just put city, state, country. cheers, zayen
    26 replies | 2247 view(s)
  • MrMoon5shine's Avatar
    01-11-2017
    Impressive to say the least ! I too, am wondering this, by watching the video over it looks like the lines were more dynamic then a standard bull line... were they climbing lines perhaps? I am thinking the extra stretch would help "absorb" some of the difference and help with the shock load forces.
    31 replies | 2940 view(s)
  • MrMoon5shine's Avatar
    01-04-2017
    a thought, i would hang the silks from one anchor point, not by running them through two as it would change the over all feeling. thinking SR vs DR here.
    49 replies | 3120 view(s)
  • MrMoon5shine's Avatar
    01-04-2017
    pre drill holes for the lags to avoid splitting the rafter, drill bit should be as big as the lag under the threaded part. to check hold drill bit over lag, you should see all the thread but very little of the core. hope that makes sence, sorry if you knew 8)
    49 replies | 3120 view(s)
  • MrMoon5shine's Avatar
    01-02-2017
    i would put a 4 x 4 beam between two rafters using joist hangers and bolt through that
    49 replies | 3120 view(s)
  • MrMoon5shine's Avatar
    12-28-2016
    and thank you for that :lol:
    119 replies | 12264 view(s)
  • MrMoon5shine's Avatar
    12-27-2016
    MrMoon5shine replied to a thread tuning a stihl 461 in Chainsaws!
    hey butch, my name is Zayen, i joined up a while back but mostly just read.
    8 replies | 1610 view(s)
  • MrMoon5shine's Avatar
    12-27-2016
    MrMoon5shine replied to a thread tuning a stihl 461 in Chainsaws!
    posted tiwce
    8 replies | 1610 view(s)
  • MrMoon5shine's Avatar
    12-27-2016
    MrMoon5shine replied to a thread tuning a stihl 461 in Chainsaws!
    i am going to say yes as i have not modded this saw at all
    8 replies | 1610 view(s)
  • MrMoon5shine's Avatar
    12-11-2016
    hoping someone can break it down to simple steps for me, I have done searches but would like some clarification on a couple things one being that i understand the three adjustments screws are High, Low and idle. so LA i adjusted warmed up but no throttle, until the chain starts moving then dial it back until it stops, High I adjusted at full throttle moving it around until it sounded the best, moving it one way then backing it off, but how and when do i move the L- screw? the reason for this retune is the weather has dropped 10 c in the last month and I just don't feel like its putting out the same power as it did, bought the saw in the spring and probably has around 300 to 400 hrs... is there any mile stone maintenance or replacements I should be doing? ie air filters... thanks in advance for any advice for this "new" saw owner (as in first time with new saws and owning them myself )
    8 replies | 1610 view(s)
  • MrMoon5shine's Avatar
    12-07-2016
    dehydration affects not only your muscles as in they don't react as fast or as precise but also your cognitive functions, basic problem solving skill and reaction time are all affected. it just reminded me of a trick i used in the past, when feeling tired, do a couple math problems in your head, if its hard to find the right answer... you're fatigued, take a break, eat, drink, grab some shade...
    22 replies | 2391 view(s)
  • MrMoon5shine's Avatar
    12-07-2016
    wise words for sure, ya i am trying to get used to running my saws in my right hand, balance is a bit odd holding a saw left handed, but some times i need the confidence or precision of using my dominant hand.
    22 replies | 2391 view(s)
More Activity
About MrMoon5shine

Basic Information

Age
32
About MrMoon5shine
Location:
Hornby Island, BC Canada
Occupation:
guy with saw that does work

Signature


I don't always do firewood, but when I do I charge my customers accordingly.

Statistics


Total Posts
Total Posts
68
Posts Per Day
0.05
Albums
Total Albums
1
Total Photos
0
General Information
Last Activity
4 Weeks Ago
Join Date
12-28-2015
Referrals
0