Tab Content
Raj's Activity
About Me
Tab Content
  • Raj's Avatar
    39 Minutes Ago
    Raj replied to a thread How'd it go today? in Odds and Ends
    Nice!
    64646 replies | 2324773 view(s)
  • Raj's Avatar
    1 Day Ago
    Raj replied to a thread milling thread in Chainsaws!
    The clamps on the bar and uprights are medium thick wall. The slided have 2 nuts and bolts that tightnen down, same thing, not thin walled
    1276 replies | 148000 view(s)
  • Raj's Avatar
    1 Day Ago
    Raj replied to a thread 088 hydrolocking in Chainsaws!
    Thanks for the info!
    28 replies | 478 view(s)
  • Raj's Avatar
    2 Days Ago
    Raj replied to a thread milling thread in Chainsaws!
    Hope you make a sale! 3Ft wide by 12ft black walnut. Need to refuel half way in the cut.
    1276 replies | 148000 view(s)
  • Raj's Avatar
    3 Days Ago
    Raj replied to a thread 088 hydrolocking in Chainsaws!
    I ran my original 088 today. Turn to run, pulled the cord a number of times and then start as usual. Choke, it burps, set to hi idle, start up. No kick back. What was going on before when it would pull the start handle out of my hand?
    28 replies | 478 view(s)
  • Raj's Avatar
    3 Days Ago
    Raj replied to a thread milling thread in Chainsaws!
    Lots of info in this thread. Sorry the recent ones are of my chainsaw mill. Today's silver maple. 3Ft wide by 8ft long, in Brantford.
    1276 replies | 148000 view(s)
  • Raj's Avatar
    1 Week Ago
    Sad turn of events.
    66 replies | 1076 view(s)
  • Raj's Avatar
    1 Week Ago
    Raj replied to a thread Woodworking in The Rec Room
    Yup! I just have to figure a way for people to smoke it or shoot it up. :lol:
    346 replies | 29194 view(s)
  • Raj's Avatar
    1 Week Ago
    Raj replied to a thread Woodworking in The Rec Room
    Some walnut. 7.5ft, 9ft and 4ft long. 12-20" wide. 3 and 4" thick. Hope I can resaw them soon to 1.5 and 2" thick. For now they sit.
    346 replies | 29194 view(s)
  • Raj's Avatar
    1 Week Ago
    Raj replied to a thread 088 hydrolocking in Chainsaws!
    Good info. In my case there has been no noticeable exhaust or burnt fuel indication.
    28 replies | 478 view(s)
  • Raj's Avatar
    1 Week Ago
    Raj replied to a thread 088 hydrolocking in Chainsaws!
    Good info! 2nd day. Put the saw to run, a bunch of pulls, then choke and start normally. No kick back or piston stop.
    28 replies | 478 view(s)
  • Raj's Avatar
    1 Week Ago
    Raj replied to a thread milling thread in Chainsaws!
    Nope. Only 404 and 3/8 ripping. I wonder how it works. Small milling job today for me. Clearing some black walnut I dropped a couple weeks ago.
    1276 replies | 148000 view(s)
  • Raj's Avatar
    1 Week Ago
    Raj replied to a thread 088 hydrolocking in Chainsaws!
    Both of them don't! Edit: Sometimes, ok, often, I will store the 088 on the mill standing up. I wonder if that would cause my issue?
    28 replies | 478 view(s)
  • Raj's Avatar
    1 Week Ago
    Raj replied to a thread 088 hydrolocking in Chainsaws!
    Yup.
    28 replies | 478 view(s)
  • Raj's Avatar
    1 Week Ago
    Raj replied to a thread 088 hydrolocking in Chainsaws!
    Great info. I tried a different method. The saw travelled with the fuel cap loose. Decomp pressed in and the switch set to run. A few pulls on the cord. Switch to choke and start as usual. No issues today. I'm thinking a partial hydro lock. I've noticed it only happens after the saw sits for a while. Fuel leaking into crank? Then sucked into cylinder? I've tried to hold decomp down before but it would still pop closed much to the discomfort of my finger.
    28 replies | 478 view(s)
  • Raj's Avatar
    1 Week Ago
    Raj replied to a thread Motorcycling. in The Rec Room
    Sad news.
    1473 replies | 105091 view(s)
  • Raj's Avatar
    1 Week Ago
    Raj started a thread 088 hydrolocking in Chainsaws!
    I've mentioned before how my one 088 with kick back and pull the starter cord out of my hand, tearing my shoulder and to ad insult to injury the handle will smash my other hand. Coil and flywheel are good. Carb rebuilt tuned to factory settings. New decomp. Still did the same. Usually when cold. Once I get over the kick back it'll start. I thought it was a cold weather issue. Nope. Does the same in the hot weather. Only when first starting for the day. I thought it might be an issue with my 088 but it does the same on the second 088 I have. I'm thinking hydro lock. Any input?
    28 replies | 478 view(s)
  • Raj's Avatar
    1 Week Ago
    Raj replied to a thread Motorcycling. in The Rec Room
    Yikes!!!
    1473 replies | 105091 view(s)
  • Raj's Avatar
    1 Week Ago
    Raj replied to a thread milling thread in Chainsaws!
    Sweet pics. How long does it take to make one pass?
    1276 replies | 148000 view(s)
  • Raj's Avatar
    1 Week Ago
    HH and HH2 here.
    736 replies | 159850 view(s)
  • Raj's Avatar
    2 Weeks Ago
    Working good. I need to tighten some bolts and screws, oil and air filter change.
    25018 replies | 486612 view(s)
  • Raj's Avatar
    2 Weeks Ago
    Some seriously big jobs going on out there. All I have today is cutting down some high stumps and grinding them.
    25018 replies | 486612 view(s)
More Activity
About Raj

Basic Information

Date of Birth
November 25, 1971 (47)
About Raj
Location:
Brantford, Ontario
Interests:
Tree climbing!
Occupation:
Rotating electrical apparatus mechanic

Signature


Peter

Statistics


Total Posts
Total Posts
6,683
Posts Per Day
3.14
Albums
Total Albums
1
Total Photos
4
General Information
Last Activity
39 Minutes Ago
Join Date
10-26-2013
Referrals
0