• BlackSmith's Avatar
    1 Hour Ago
    4315 replies | 98827 view(s)
  • BlackSmith's Avatar
    4 Hours Ago
    https://youtu.be/5sDmms-WmD8 https://youtu.be/L2c-tUf3WaE
    4315 replies | 98827 view(s)
  • BlackSmith's Avatar
    4 Days Ago
    “If I get a call from a potential client who goes out of their way to express opposing political views from me then I simply figure that into my bid.”
    4315 replies | 98827 view(s)
  • BlackSmith's Avatar
    4 Days Ago
    BlackSmith replied to a thread Woodworking in The Rec Room
    Just one template Pete. Stig. What I did was glue up a 3/8” thick board of Red Oak over a 3/8” thick board of Honduran Mahogany with the grain of each running perpendicular to each other. That made the blank the project was cut from. The staves are cut from black walnut. I wanted something different. The contrasting colors of the wood turned out ok, I think.
    218 replies | 16795 view(s)
  • BlackSmith's Avatar
    4 Days Ago
    BlackSmith replied to a thread Woodworking in The Rec Room
    Yes Sean, cut about 1/16” thick. A different basket but basically the same procedure...
    218 replies | 16795 view(s)
  • BlackSmith's Avatar
    4 Days Ago
    BlackSmith replied to a thread Woodworking in The Rec Room
    Spacy..?
    218 replies | 16795 view(s)
  • BlackSmith's Avatar
    5 Days Ago
    BlackSmith replied to a thread Woodworking in The Rec Room
    Pair of baskets I made recently for a wedding present...
    218 replies | 16795 view(s)
  • BlackSmith's Avatar
    1 Week Ago
    Post the “money shot”... :D
    4 replies | 61 view(s)
  • BlackSmith's Avatar
    1 Week Ago
    Give tractorhouse.com a try
    4 replies | 61 view(s)
  • BlackSmith's Avatar
    1 Week Ago
    something something globalism... ::runs::
    2 replies | 74 view(s)
  • BlackSmith's Avatar
    1 Week Ago
    BlackSmith replied to a thread milling thread in Chainsaws!
    Good advice guys. Thought I’d get at least one “man up cupcake”. :D
    1110 replies | 114735 view(s)
  • BlackSmith's Avatar
    1 Week Ago
    BlackSmith replied to a thread milling thread in Chainsaws!
    I think it’ll cut 47” slabs. Shame it’s the anti-anti-vibe version. 20 minutes and your arms are numb.
    1110 replies | 114735 view(s)
  • BlackSmith's Avatar
    1 Week Ago
    BlackSmith replied to a thread milling thread in Chainsaws!
    Picture of said animal... Even gots a home made set of left coast dogs and a 1/2” drive sprocket so some day I can pretend to be Billy Badazz. :D
    1110 replies | 114735 view(s)
  • BlackSmith's Avatar
    1 Week Ago
    BlackSmith replied to a thread milling thread in Chainsaws!
    I’ll take a picture of it when I get home for ya. Gotta take the boyz to the vet for shots and drop the wife off at the beauty parlor (for an estimate) then I’m done for the day.
    1110 replies | 114735 view(s)
  • BlackSmith's Avatar
    1 Week Ago
    BlackSmith replied to a thread milling thread in Chainsaws!
    Well, I’m not trying to one up ya but I paid exactly $100 for this one and wasn’t even looking for a mill. A guy I know that collects old hit’n mis engines was looking for a big saw for me. Called me one day and said to stop by cause he found one but it needed some work. Walked in his shop and he said “there it is ya want it?” pointing to a 090 with the mill attached. I just laughed at him figuring he was joking. Said he was serious so I asked what he wanted for it. Said give me $100, it was in with a bunch of engines he bought at auction and had no use for it. I asked him if he realized what it was worth and he said it didn’t matter, just another saw to him. I jumped on it. I cleaned out the carb and put a gasket kit in it and dug a half a tank of varnish out of the gas tank, put a hard nose bar on it and bought three skip 404 chains for it. Got $400 total in it. Runs like the beast it is.
    1110 replies | 114735 view(s)
  • BlackSmith's Avatar
    1 Week Ago
    BlackSmith replied to a thread milling thread in Chainsaws!
    I have a Granberg and I don’t see anything special that would justify the price.
    1110 replies | 114735 view(s)
More Activity
About BlackSmith

Basic Information

About BlackSmith
Biography:
Bob
Location:
Upnya WV
Interests:
alt energy, puppy dogs, long walks on the beach
Occupation:
pipe welder/fitter

Signature


˙ǝuılƃıs ʎɯ uı ʇnd oʇ ɹǝʌǝlɔ ƃuıɥʇʎuɐ ɟo ʞuıɥʇ ʇ,uɐɔ I

Statistics


Total Posts
Total Posts
5,140
Posts Per Day
1.04
General Information
Last Activity
1 Hour Ago
Join Date
03-06-2005
Referrals
0